Views: 1152 Author: Site Editor Publish Time: 2026-11-18 Origin: Site
CO2 heat pumps offer a practical route to electrifying hot water production while using a refrigerant with a low direct climate impact. Their transcritical operating cycle is particularly suited to heating cold water to a high delivery temperature. For building owners, engineers and project developers, the main opportunity lies in matching this technology to the right temperature profile, storage arrangement and daily demand. This article explains how CO2 heat pumps work, their advantages and the applications where careful system design can deliver the greatest value.
A CO2 heat pump uses carbon dioxide, designated R744, as the working fluid in a closed refrigeration circuit. Electricity drives a compressor that upgrades heat collected from air, water or another available source and transfers it to a useful heating load. CO2 identifies the refrigerant rather than the heat source: an air-source CO2 heat pump draws energy from outdoor air, while water-source designs collect heat from water.
R744 has zero ozone depletion potential and a global warming potential of 1 by definition. It is non-flammable, but its high operating pressure requires purpose-designed components and qualified servicing. Refrigerant selection alone does not determine the carbon footprint of an installation; electricity generation, system efficiency and equipment operation also matter.
For hot water production, CO2 heat pumps typically operate in a transcritical cycle. The high-pressure side runs above the refrigerant’s critical pressure, and heat is transferred through a gas cooler rather than a conventional condensing heat exchanger. Four stages repeat continuously to move heat from the source into the water.
2.1 Heat Absorption and Compression
In an air-source unit, low-pressure refrigerant absorbs heat from outdoor air in the evaporator and evaporates. The compressor then raises the vapour pressure and temperature, supplying the temperature lift needed for useful water heating. Electricity powers the compressor, fans and associated controls.
2.2 Heat Delivery and Expansion
The hot, high-pressure CO2 releases heat as it cools in the gas cooler. Water flowing through the other side of the heat exchanger gains this energy without mixing with the refrigerant. The CO2 then passes through an expansion valve, reducing its pressure and temperature before returning to the evaporator.
2.3 Why the Water Temperature Profile Matters
CO2 cools through a substantial temperature range during heat delivery. A counterflow heat exchanger can match this profile to water entering cold and leaving hot. Lower inlet water temperatures generally support better performance. High return temperatures, excessive tank mixing and poorly arranged recirculation can reduce efficiency, so the hydraulic design is as important as the heat pump itself.
High-temperature water production. Suitable CO2 systems can supply hot water at temperatures useful for storage and demanding water-heating duties. The achievable temperature and capacity depend on the selected model and operating conditions; a maximum outlet temperature should never be treated as a guarantee across the entire ambient range.
Low direct refrigerant climate impact. R744 avoids the high direct warming impact associated with many conventional refrigerants. Its environmental value is strongest when combined with efficient system operation and lower-carbon electricity.
Efficient use of electricity. By transferring heat rather than producing all of it through resistance heating, a heat pump can deliver more thermal energy than the electricity it consumes. Actual savings depend on inlet and outlet temperatures, ambient conditions, auxiliary energy and the heating system being replaced.
Compatibility with thermal storage. A correctly sized hot water tank can store heat produced ahead of peak demand. Where tariffs and operating schedules make this worthwhile, controls can shift part of the electrical load to more favourable periods or coordinate operation with onsite solar generation.
The coefficient of performance, or COP, is useful heat output divided by electrical input at a stated test condition. A COP of 3 means that 1 kWh of electricity delivers 3 kWh of heat at that condition. This is an explanatory example, not a rating for the illustrated product. Comparisons should use the same ambient temperature, inlet water temperature, outlet temperature and measurement boundary.
Annual energy use also includes tank heat loss, distribution losses, circulation pumps, defrost and any backup heating. Assess hot water demand over a full day and across the year, rather than selecting equipment from a single rated COP. Preserve tank stratification where the system is designed for it, and arrange recirculation returns to avoid unnecessarily warming the heat pump inlet.
Air-source installations need suitable airflow, service access, condensate drainage and frost protection. CO2 refrigerant circuits require pressure-rated equipment and appropriate safety provisions. Indoor refrigerant-containing equipment also needs a site-specific assessment of ventilation and leak detection requirements. Hot water storage and distribution must address local hygiene requirements and scald protection.
5.1 Homes and Apartment Buildings
Domestic hot water is a natural application, particularly where cold mains water can be heated into a stratified storage tank. Central systems serving apartments need demand diversity, storage volume and recirculation losses to be assessed together. Space heating is also possible with suitable equipment, but the return temperature and seasonal load must be checked rather than assuming the same efficiency as a cold-water heating duty.
5.2 Hotels and Commercial Facilities
Hotels, student accommodation, sports facilities and other buildings with regular hot water consumption can benefit from a storage-based approach. Equipment capacity and recovery time should reflect peak draw-off periods. Where continuity of service is essential, the design should include an appropriate backup or redundant arrangement.
5.3 Industrial Hot Water and Heat Recovery
Suitable commercial and industrial CO2 systems can support wash water, cleaning and process hot water duties. Water-source designs may recover useful heat from compatible waste streams. Each process requires checks of temperature, water quality, heat exchanger compatibility and available source energy. The residential-size unit illustrated here should not be assumed to meet industrial loads.
1. Define the daily hot water volume, peak demand, required delivery temperature and available recovery time.
2. Confirm the local design ambient temperature, source conditions and installation constraints.
3. Request capacity and electrical input data at the actual inlet and outlet water temperatures, including cold-weather operation where relevant.
4. Size storage and design the hydraulic circuit to manage stratification, recirculation and backup heating.
5. Compare annual system energy use and lifecycle cost using local tariffs and realistic demand profiles.
6. Verify applicable approvals, pressure safety requirements, commissioning procedures and local service support.
CO2 heat pumps combine a natural refrigerant with a cycle well suited to high-temperature hot water production. Their value depends on the complete installation: heat source, water temperatures, storage, controls and demand profile. For a project-specific selection, contact NULITE with the required hot water volume, inlet and outlet temperatures, local climate and installation details so that the proposed equipment can be assessed against the real duty.
content is empty!